Your network contains two DHCP servers. The DHCP servers are named DHCP1 and DHCP2. The internal network contains 1,000 DHCP client computers that are located on a single subnet. A routerseparates the internal network from the Internet. The router has a single IP address on the internal interface. DHCP1 has the following scope information. èStarting IP address: 172.16.0.1 èEnding IP address: 172.16.7.255 èSubnet mask: 255.255.240.0 You need to provide a fault-tolerant DHCP infrastructure that supports the client computers on the internal network. In the event that a DHCP server fails, all client computers must be able to obtain a valid IP address. How should you configure DHCP2?()
You are the network administrator for TestKing. All network servers run Windows Server 2003. You administer a server named TestKing76. You need to configure TestKing76 to function as a streaming media server for TestKing.com's content team. The content team wants TestKing76 to provide the fastest performance and the most available space possible. Redundancy is not import. TestKing76 currently has three identical, unpartitioned hard disks available. You need to configure the disks to meet the content team's requirements. What should you do?()
Your network consists of a single Active Directory domain named contoso.com. All network servers run Windows Server 2003 Service Pack 2 (SP2). You have a DNS zone named contoso.com. The zone is configured to support dynamic updates. All servers in the company are registered in the contoso.com zone. You change the IP address of a server named Server1. From a server named Server2, you attempt to ping Server1 by host name, but the request fails. You successfully ping the new IP address of Server1. You need to ensure that Server2 can connect to Server1 by using the Server1 host name. Which two actions should you perform?()
You are a network administrator for your company. The network contains a Windows Server 2003 computer named Print1 that functions as a print server. Print1 contains a printer named MarketingPrinter. Users report that print jobs they submit to the MarketingPrinter take a long time to print. You immediately examine Print1 and conclude that the server is performing at acceptable levels. You need to identify the problem. What should your next step be? ()
You are the administrator of your company’s network. The network is configured as shown in the exhibit. You want to install Windows 2000 Professional on 10 non-PXE-compliant computers on the marketing segment of your network. The 10 computers do not have operating systems installed. You attempt to load the computers by using an existing RIS image that is on the RIS server. You find that the 10 computers cannot connect to the RIS server. You verify that existing client computers on the network can connect to network servers, including the RIS server. You then check the network servers and find that the Windows NT Server 4.0 computer running WINS has stopped responding due to hard disk failure. You want to enable the computers to connect to the RIS server. What should you do?( )
Your network consists of a single Active Directory domain.? All domain controllers run Windows Server 2008 R2. You need to identify the Lightweight Directory Access Protocol (LDAP) clients that are using the largest amount of available CPU resources on a domain controller. What should you do()
A network planning diagram shows a large internetwork with many routers. The configurations show that OSPF has been enabled on all interfaces, I P addresses correctly configured, and OSPF workinG. For which of the following cases would you expect a router to create and flood a Type 2 LSA?()
You are the administrator of your company’s network. You want to install Windows 2000 Professional on 10 non-PXE-compliant computers that are on the marketing segment of your network. You start one of the computers by using a RIS boot disk. However, you cannot connect to the RIS server. You verify that existing client computers on the network can connect to network servers, including the RIS server. You discover that the network router does not support BOOTP. You want to enable the new computers to connect to the RIS server. What should you do? To answer, click the select and place button, and then drag the appropriate server to the place server here boxes on the network (Note: Both boxes must be filled. If a box does not require a server, use No server needed)
Your network consists of a single Active Directory domain. All servers run Windows Server 2003 Service Pack 2 (SP2). You have a member server named Server1 that is configured as a DHCP server. You install a new stand-alone server named Server2 in the same subnet as Server1. You install the DHCP service on Server2. You need to ensure that Server2 can assign IP configurations to clients on the subnet. What should you do first?()
Your network contains one Active Directory domain. You have a member server named Server1 that runs Windows Server 2008 R2. The server has the Routing and Remote Access Services role service installed.You implement Network Access Protection (NAP) for the domain.You need to configure the Point-to-Point Protocol (PPP) authentication method on Server1.Which authentication method should you use?()